Product Description:

Our very own PHT-027 has been re-engineered to bring you the most advanced and most functional water tester in the market today, it has a BUILT-IN RECHARGEABLE BATTERY with USB TYPE charger to save you from the hassle of buying, placing & replacing button batteries. Now all you have to do is charge the Built-in Rechargeable Battery the first time you use it, then recharge it again as needed with standard charging time of approximately two (2) hours. The include PH electrode is BNC type so you can easily replace it anytime without buying the whole set! Plus you get a FREE ORP electrode which is also replaceable!

The PHT-027 can measure not just six paramater but 7 paramaeters this includes, ORP(MV), pH, CF, EC, TDS(PPM) °F and °C. The Multi-parameter Water Quality Monitor is a versatile, high-accuracy multi-parameter instrument with reliable multi probe system and with all the functionality of a multi-parameter system. It can provide simultaneous measurements results.

It so easy to use and indeed an affordable one, which made it possible for non-technical and technical personnel alike to measure dissolved solids, pH, ORP, conductivity and temperature on the spot, accurately and inexpensively throughout a variety of applications. No more switching meters to measure the pH, °C or °F and then the EC, CF or TDS of a solution. Tests that usually require different tools but with PHT-027 it covers all seven measurements.

High acidity or alkalinity can cause direct physical damage to skin, gills eyes and reproductive cycle of fish. Prolonged exposure to unwanted excess substances can cause stress with sometimes-fatal consequences. Changes in either acidity or alkalinity can exert a powerful influence over both water quality and water chemistry, and will have a marked effect on the fish health and filter activity.The fast, efficient, accurate and portable, more precise measurement meets the requirements of your routine multi-measurements. And it comes with FREE pH6.864 and pH4.003 CALIBRATION SOLUTIONS and a USB TYPE BATTERY CHARGER.

Simultaneously analyze water quality parameters with a single submersible system with USB technology! This the real deal. Here at GainExpress, not only do you get 2 FREE calibration solutions and USB type battery charger, you also get a FREE ORP electrode. Only GainExpress gives you a FREE ORP Electrode.

Buy Now!

• With Built-in Rechargeable Battery that can last long!
• USB Type battery charger
• Provides 7 Parameters
• Supplied complete with probe, pH electrode, protective cap and calibration screwdriver.
• FREE pH6.864 and pH4.003 CALIBRATION SOLUTIONS
• FREE pH ORP Electrode
• Provides large LED display for easy monitoring of pH accurately plus the values are readable within few seconds
• Manual is provided for quick and easy installation and to best utilize PHT-027
• Choice of wall-mount or hung in installing the controller
• Includes a BNC connection for use with a PH Electrode
• With fast response and easy to calibrate replaceable pH electrode and comes with complete calibration fluids
• It is very reliable, stable and transportable
• The operation is simple and comfortable
• The unit can be simply calibrated in one-point with a mini-screw driver and has a large digital graphic display for maximum efficiency

 

Specification:

• Range

  EC : 0.00~19.99EC
  CF : 0.0~199.9CF
  TDS : 10~19990ppm
  PH : 0.00~14.00PH
  mV: 0~±1999mV
  °C : -50°C~70°C (°F : -58°F~158°F)
  

• Resolution
  EC : 0.01EC
  CF : 0.1CF
  TDS : 10ppm
  PH : 0.01PH
  mV: 1mV
  °C : 0.1°C (°F : 0.2°F)
  
  
• Accuracy
  PH : ±0.1PH       
  °C : ±1.0°C      
  mV: ±0.1%F.S±1digit
  EC, CF, TDS : ±2% F.S
• Operating Temperature : 0°C~50°C
• Automatic Temperature Compensation (ATC) : 0°C~50°C
• BUILT-IN BATTERY PACK with USB Type Battery Charger
• Dimensions: 155mm x 86mm x 22mm
• Weight: 230g

 

Operating Information:

1. If it will be used for the first time, the meter has to be charged first. After plugging in the USB connector to the meter, slide the switch on the upper-right side of the meter to move the slider to ON position. Charge the built-in rechargeable battery for two hours before you start using PHT-027.
2. Remove the pH electrode's protective cap and connect the the BNC connector to the pH electrode input terminal which can be found on the left part of the unit.
3. Immerse the two electrode in the solution to be tested. Stir gently and wait for the reading to stabilize.
4. Press button when choosing °C or °F. Press button when choosing EC, CF, or PPM to show precise measurement respectively.
5. Replace ORP electrode if you need to measure ORP related measurements. Do step #4 when changing pH to ORP electrode.
6. After using, turn off the meter. Rinse the electrode with distilled water to minimize contamination. Put back protective cap on to pH electrode.

   GENERAL REMINDER:

   • Be sure to put back the electrode protective cap after each use.
   • The glass bulb of the electrode is fragile. Use it carefully and cautiously. Do not touch it with hard or pointy objects nor with your fingertip.
   • When removing the excess water inside the electrode mouth, wipe gently and carefully.
   • Clean the electrode before and after you use the unit. It can only be clean with distilled or ionized water specifically

 

Calibration Settings:

• PH Calibration
  • Immerse the electrode in PH 6.86 buffer (calibration) solution, and gently shake it.
  • Allow the reading to stabilize. Use the mini-screw driver to turn the "pH6.86" calibration knob until the displays show "6.86"pH. Rinse the electrode with distilled water, and wipe it with filter-paper.
  • Immerse the electrode in pH4.01 buffer (calibration) solution until "4.01pH" appears. Rinse the electrode with distilled water, and wipe it with filter-paper.
  • Immerse the electrode in pH9.18 buffer (calibration) solution until "9.18pH" appears. pH9.18 buffer solution is not included in the package.
    
    
• EC, CF, ppm calibration
  • Press button, choose EC for operating. Immerse the meter in 12880µ s/cm (12.88EC) calibration solution. 12880µ s/cm or 12.88EC buffer solution is not included in the package.
  • Allow the reading to stabilize. Use mini-screw driver turn the CAL Calibration knob until "12.88EC" appears. Rinse the electrode with distilled water, and wipe it with filter-paper.
  • Immerse the meter in "1413µ s/cm (1.41EC)" calibration solution until "1413(1.41EC)" shows. 1413µ s/cm or 1.41EC buffer solution is not included in the package.


• The instrument's pH range must be re-calibrated whenever:
  • The electrode has not been in used or has been in the storage for 4 or 5 months from the last calibration
  • the electrode has been in used very often in a day
  • the electrode has been replaced or
  • the utmost accuracy is required

Accessories included:

• BUILT-IN RECHARGEABLE BATTERY
• FREE Detachable ORP Electrode only at GainExpress!
• USB Type Battery Charger
• FREE pH6.864 and pH4.003 CALIBRATION SOLUTIONS
• Detachable pH electrode
• User's Manual
• Mini-Screw Driver
• Metal Holder for Hanging PHT-027
• 3 Cable Holders with suction cap

 

Warranty: 2 years warranty